EQUIPMENT SERIES
Film cutting and layup with edge control
Suzhou SC-Solar Equipment Co., Ltd. ↗This SC Solar station cuts encapsulant film or backsheet from the roll and places it in the layup. It steers the web with deviation correction and changes rolls by hot-melt splicing without a stop. Cutting accuracy is listed at ±1.5 mm, so placement accuracy and splice handling are the points to settle in the quotation.
Covers the edge-finding EVA/POE cutting and layup station, which SC Solar also lists for backsheet. Splice behaviour and material fit depend on your film grade and process.
General illustration of module assembly equipment, not a photograph of this model. Ask the manufacturer for current photographs and layout drawings of the configuration offered.
START WITH YOUR PRODUCTION TASK
Define your rolls, materials and cut and placement targets, agree tension and splice handling with SC Solar in writing, then accept the station on repeat cuts and finished layups through roll changes and size switches.
SOURCE-LINKED DATA
Published specifications
Values below are published by the manufacturer, each with the date its source was checked. Ask for the figures that apply to your configuration and material in the quotation.
The manufacturer has not published a complete specification table for this entry. Request the exact offered drawing and operating limits.
01 · Manufacturer information
How the film path and roll changes affect usable material
The station cuts and places encapsulant film and backsheet, corrects web deviation, changes rolls by hot-melt splicing without stopping and switches module size with one click. SC Solar lists no roll diameter or mass, core size, film thickness, allowed tension or splice build. Name your exact EVA, POE or backsheet grade, since each web behaves differently on the machine. If the film drifts after cutting and causes rework, SC Solar's EVA repositioning and pre-melt station can square and tack the sheet before the strings go on.
The table lists ±1.5 mm cutting accuracy and a 12-second cycle. It gives no separate tolerance for where the film lands in the layup. The non-stop roll change comes without waste figures, splice tracking or laminate results. Agree which spliced lengths are scrapped and which can be used before you compare line uptime.
02 · Manufacturer information
Film cutter figures from SC Solar
| Item | Listed value | What to check |
|---|---|---|
| Module size | 1650–2550 × 990–1450 mm | Your cut sizes and placement. |
| Cutting accuracy / cycle | ±1.5 mm / 12 s | Cut size measured apart from film alignment in the layup. |
| Power and supply | 8 kW; AC380 V±5%, 3P+N+PE, 32 A, 50/60 Hz | Site electrical requirements. |
| Air / noise | 0.5–0.8 MPa / ≤70 dB | Air flow and the noise test method. |
| Size and weight | 6250×2750×2000 mm / 3500 kg | Room for rolls and service. |
03 · PVYard procurement analysis
Define the film, the cut and the splice
Rolls
Grade of EVA, POE or backsheet, thickness, width, core and roll mass, and your film maker's handling limits.
Cut and placement
Length, width, squareness, edge finish, layup position and wrinkle or stretch limits, each measured on its own.
Splices
How splices are detected and marked, which lengths are used or scrapped, where waste goes, and the safety and service scope of a roll change.
04 · PVYard procurement analysis
Trial steady running and roll changes
Fix grade and settings
Agree the web path, the tension and cutting settings SC Solar controls, and who owns the recipe.
Measure cuts and layups
Check size, edges and placement across full and nearly empty rolls and each material you run.
Run splices and size changes
Track splices and rejects, and repeat size switches to see that one click gives the same result every time.
Count total output
Include roll changes, cleaning, faults and restarts when you measure accepted sheets and waste.
05 · PVYard procurement analysis
Film cutter questions
Is ±1.5 mm the placement accuracy?
SC Solar labels it cutting accuracy. Agree a separate placement tolerance and test it.
Can spliced film go into modules?
That depends on your material and laminate checks. Ask SC Solar to state in writing which splice sections are rejected.
Does it run every POE or backsheet grade?
The page names material types only. Run your grades in a trial and have the result confirmed in writing.
TURN THIS INTO A CLEAR REQUEST
Ask about this product
Include the product-specific questions above and replace every bracket with your actual requirement. Save your edited text to your sourcing brief, then review it before submitting an enquiry. Saving a brief does not send it to a manufacturer.
Sources
Manufacturer information and our buying guidance are labelled section by section above. Each source below shows the date it was checked.
SC Solar edge-finding EVA/POE cutting page ↗
Source check: 2026-10-11 · Cutter description, numeric table and equipment picture.
Compare equipment for a related task
These entries are in the same category; check each one's specifications and configuration.