EQUIPMENT SERIES
TCDY-BJ1 family · Two-level three-chamber laminator
Yiheng Technology ↗The TCDY-BJ1 stacks two levels, each passing modules through a lamination chamber, a curing chamber and a water-cooling chamber in turn. Upper and lower levels transfer independently.
Yiheng's 2017 detail page and its parameter sheet give three model rows for this family, set out in one table here.
General illustration of module assembly equipment, not a photograph of this model. Ask the manufacturer for current photographs and layout drawings of the configuration offered.
START WITH YOUR PRODUCTION TASK
Pick the working size, settle the module stack and the cooling and transfer package, then accept both levels through all three stages on measured accepted output.
SOURCE-LINKED DATA
Published specifications
Values below are published by the manufacturer, each with the date its source was checked. Ask for the figures that apply to your configuration and material in the quotation.
The manufacturer has not published a complete specification table for this entry. Request the exact offered drawing and operating limits.
01 · Manufacturer information
Three stages on each level
Lamination, curing and water cooling each get their own chamber. Upper and lower levels transport independently, and each level links its three stages with synchronised transfer. Yiheng mentions automatic cleaning and an intelligent control mode. The page leaves out the transfer protocol, cooling-water flow and loaded cycle time, so ask for them. Yiheng's two-level two-chamber laminator drops the water-cooling chamber, and our guide to specifying a PV module laminator lists the cooling and transfer points to settle with either family.
Yiheng cites 200 MW a year without module wattage, recipe, shift calendar, reject rate or uptime. The 386 kW figure is installed power, and energy per module needs measuring on site. Weight runs from 80 to 110 tonnes and length changes by model, so foundation and layout work starts from the drawings for the row you choose.
Source: Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet
02 · Manufacturer information
TCDY-BJ1 models
| Model | Lamination size mm | Dimensions mm | Installed kW / weight t |
|---|---|---|---|
| TCDY-BJ1/J1-5824 | 5800×2400 | 34050×3360×3250 | 386 / 110 |
| TCDY-BJ1/J1-5624 | 5600×2400 | 33650×3360×3250 | 386 / 105 |
| TCDY-BJ1/J1-4624 | 4600×2400 | 28300×3360×3250 | 336 / 80 |
Source: Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet
03 · PVYard procurement analysis
Cooling and site items for the BJ1 order
Cure recipe
State the encapsulant and glass stack, module geometry and cure and adhesion limits. Ask how far Yiheng's lamination and curing recipe support extends.
Water circuit
Get water temperatures, flow and pressure, heat rejection, and the connection and service needs of the cooling chamber.
Hot-to-cool transfers
Define buffers, conveyor levels, module support and allowed movement between the hot and cooled states, and the condition modules leave in.
Foundation and power
Size the design from the chosen row's weight and installed power, and get load and electrical drawings. Measure consumption separately.
Source: Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet
04 · PVYard procurement analysis
BJ1 acceptance on both levels
Approve the row
Fix size and model, module stack, chamber interfaces and the infeed and outfeed conditions.
Test loaded processing
Map thermal and curing conditions and inspect the agreed laminate results on the upper and lower levels.
Check cooling and movement
Measure exit condition, module support and handling damage across transfers over representative cycles.
Accept a production run
Include cleaning, stops and recovery of the water circuit, and record accepted output and energy under a stated calendar.
Source: Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet
05 · PVYard procurement analysis
TCDY-BJ1 questions
What cooling-water supply does the BJ1 need?
The sheet gives no flow or heat-load figures. Ask Yiheng for water temperature, flow, pressure and heat rejection for your model.
Is 386 kW the running load?
It is installed power. Measure actual demand and energy per module during acceptance.
Does the 200 MW figure cover all three models?
Yiheng gives one figure with no recipe, wattage or calendar per model. Ask for output by model and by module type.
Source: Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet
TURN THIS INTO A CLEAR REQUEST
Ask about this product
Include the product-specific questions above and replace every bracket with your actual requirement. Save your edited text to your sourcing brief, then review it before submitting an enquiry. Saving a brief does not send it to a manufacturer.
Sources
Manufacturer information and our buying guidance are labelled section by section above. Each source below shows the date it was checked.
Yiheng TCDY-BJ1 three-chamber laminator page with parameter sheet ↗
Source check: 2026-10-11 · 2017 detail page describing the three chambers and independent levels, with a three-row sheet of sizes, power and weight.
Compare equipment for a related task
These entries are in the same category; check each one's specifications and configuration.