EQUIPMENT SERIES
TCZY-GF1 family · Single-level two-chamber laminator
Yiheng Technology ↗Two chambers sit next to each other on a single level, linked so modules pass from one to the other. Yiheng fits the line with automatic cleaning, PLC operation and PID temperature control.
Yiheng's product page and model sheet give three TCZY-GF1/F3 sizes. The catalogue says 100 MW with lamination and curing in separate chambers; the product page says 50 MW with both steps completed together.
General illustration of module assembly equipment, not a photograph of this model. Ask the manufacturer for current photographs and layout drawings of the configuration offered.
START WITH YOUR PRODUCTION TASK
Ask Yiheng for a chamber diagram and the basis of its output figure, then run your module stack through both chambers with loading, unloading and cleaning in the timed run.
SOURCE-LINKED DATA
Published specifications
Values below are published by the manufacturer, each with the date its source was checked. Ask for the figures that apply to your configuration and material in the quotation.
The manufacturer has not published a complete specification table for this entry. Request the exact offered drawing and operating limits.
01 · Manufacturer information
Which chamber does what
In its catalogue Yiheng calls this a conventional double-linked family for 100 MW automatic lines, with the side chambers laminating and curing independently. The product page gives 50 MW and says lamination and curing are completed together in a single-level, two-chamber layout. The split of work between the chambers sets the cycle, so ask Yiheng which description matches the machine you are quoting. For a water-cooled exit on one level, compare Yiheng's single-level three-chamber laminator, and take the chamber questions from the buying notes on specifying a PV module laminator.
The page mentions automatic cleaning, PLC operation, PID temperature control and energy saving, without a measured consumption figure. Its three rows give working area, installed power, footprint and mass. Vacuum, chamber timing, module stack and yield are left for the quotation. Other makers' module laminators are grouped in one category if you want to compare chamber layouts and parameter sheets.
02 · Manufacturer information
TCZY-GF1/F3 models
| Model | Working size mm | Dimensions mm | Installed kW / weight t |
|---|---|---|---|
| TCZY-GF1/F3-5824 | 5800×2400 | 26200×3360×1986 | 188 / 40 |
| TCZY-GF1/F3-5624 | 5600×2400 | 25600×3360×1986 | 188 / 36 |
| TCZY-GF1/F3-4624 | 4600×2400 | 21300×3360×1986 | 163 / 31 |
03 · PVYard procurement analysis
Three things to pin down with Yiheng
Chamber diagram
Where does pump-down, lamination, cure and venting happen? Do the two chambers overlap in time, and what state must the module be in at each transfer?
Material limits
State your glass and encapsulant, module size, support and the cure, adhesion, void and damage limits, with where and how you measure them.
Output basis
Ask which of the two MW figures applies and on what module wattage, full cycle, shifts and downtime. Confirm the model is still in production.
04 · PVYard procurement analysis
Trial the agreed sequence
Approve the model
Sign off the size, what each chamber does and the transfer drawings.
Measure heat and laminate quality
Map the loaded chambers and record material and cell results by position over several batches.
Time linked cycles
Run loading, both chambers, unloading, buffers and cleaning with a logged time record.
Test faults
Stop the line between chambers, reject a module and restart, then report good output and energy used.
05 · PVYard procurement analysis
Buyer questions on the TCZY-GF1
Is output 50 MW or 100 MW?
Yiheng's catalogue says 100 MW and its product page says 50 MW. Ask Yiheng which figure applies and on what basis.
Does curing happen in its own chamber?
The two Yiheng descriptions word this differently. A chamber diagram with timing answers it for your order.
Can I use installed kW to estimate energy per module?
Installed power is a connection figure. Measure real consumption against good modules over full cycles.
TURN THIS INTO A CLEAR REQUEST
Ask about this product
Include the product-specific questions above and replace every bracket with your actual requirement. Save your edited text to your sourcing brief, then review it before submitting an enquiry. Saving a brief does not send it to a manufacturer.
Sources
Manufacturer information and our buying guidance are labelled section by section above. Each source below shows the date it was checked.
Yiheng TCZY-GF1 product page with size table ↗
Source check: 2026-10-11 · Gives the two-chamber layout, the 50 MW figure and the three GF1/F3 rows; the catalogue entry for the same family says 100 MW.
Compare equipment for a related task
These entries are in the same category; check each one's specifications and configuration.